Tender For design, manufacture, supply, installation, testing and commissioning of passenger transparent glass type lift (8-13 passengers capacity) complete with all associated electrical works and accessories as per site requirements and rdso specifications/system, under the supervision of the site in-charge. the lift shall be of capsule type with a rated load of 544 kg, (g+4 or as per site), 1-5 openings/access sides, floor destinations g, 1, 2, 3,4 and a travel height of approximately 18 m. it shall operate at a speed of 1.0 m/s with a variable voltage variable frequency (vvvf) drive and full collective control (simplex type). the lift shall have automatic glass doors (700 mm w x 2000 mm h), pit depth 1600 mm, minimum floor-to-floor height 2600 mm, headroom 5000 mm, and internal car height 2200 mm. the car shall be finished with glass walls, led lighting, fan, stainless steel handrail, and a voice announcement system to indicate floor position and movement. it shall include an attractive car operating panel with push buttons for door open/close, alarm, position indicator, pre-announcing arrows, and full segment display. landing doors shall be automatic glass type with indicators. the system shall include 8x19s fibre core self-lubricating ropes (usha martin make), monoblock control panel with closed-loop control, self-diagnostic features, safety torque off, fireman control, automatic rescue device, overload sensor,emergency alarm/light, and ?out of service? mode. a lockable storage room of approximately 400 sq.ft for control panel and related equipment shall be provided. cost includes free maintenance of two years during warranty of lift as per rdso spec.rdso/2013/em/spec/0016 (rev'2') - 2025 make-johnson/otis/schindler/omega elevators or equivalent. hsn code- 84281011.
Tender For corrigendum : supply of electrical engineering equipment oh35 c c -three phase induction motor coupled with dc machine , three phase salient pole synchronous motor coupled with dc machine , three phase cylindrical rotor type synchronous motor coupled with dc machine , single phase transformer , single phase induction motor with loading arrangement , three phase slip-ring induction motor , three phase, autotransformer variac , lcr meter , portable ac volt meter 0-250 by 500v , portable ac volt meter 0-150 by 300v , portable watt meter voltage range 300-600v, current range 5-10a , portable lpf watt meter voltage range 300600v, current range 5-10a , portable lpf watt meter voltage range 150-300v, current range 1-2a , portable upf watt meter 75-150v, 5-10a , rheostat 0-50 ohm, current- 0-5a , analog tachometer , voltage sensor , current sensor , digital storage oscilloscope , function generators , dc source , single phase variac , rheostat , multimeter , inductor , cyclone fpga based battery management system , 500w llc converter based electrical vehicle quick charger with front end pfc correction , process control simulator , lead lag network compensator , pcb rapid prototyping machine , qled dot display, capacitive touch 10 inches , lidar distance sensor , eye tracker with ai accelerator , high voltage differential probe , ac by dc current probe , complete set-up for study of speed control of vsi fed induction motor squirrel cage drive operated in direct torque control mode , single phase power quality analyser , single phase auto transformer variac , rheostat , 210ohm - 2 and half a , rheostat, 50ohm -5a , ac volt meter , 0-150 by 300v , ac volt meter , 0-250 by 500v , ac ammeter, 0-5 by 10a , watt meter, 0-300by 600v , 0-5by10a , numerical 1-phase differential protection relay , numerical 1-phase or 3phase negative sequence current relay , numerical 1-phase or3-phase directional over current relay , magnetic and electric field meter , vacuum oven , ultrasonic probe sonicator , digital viscometer , high voltage ac-dc test set , flash and fire point tester , oil-bdv teat set with replaceable electrodes , acoustic sensor , tev sensor , digital storage oscilloscope with probes , sliding rheostat 50ohm,2a , sliding rheostat 100ohm,2a , sliding rheostat 200 ohm,2a , sliding rheostat 300 ohm,2a , wire wound resistor 10ohm , 1 a , wire wound resistor 30 ohm , 1 a , wire wound resistor 50 ohm , 1 a , wire wound resistor 60 ohm , 1 a , l-c-r meter , ammeter 0 - 200 ma , ammeter 0-500 ma , 3-ph variac , anderson bridge with accessories , schering bridge with accessories , wien bridge oscillator trainer , three phase auto transformer variac , portable lpf wattmeter , table top digital voltmeter , table top digital ammeter , table top digital wattmeter , digital energy meter , ni usb6001 daq cards , ni analog discovery 3pro , analog and digital electronics trainer kit , dc power supply , arduino boards , photovoltaic module study kit , afg , dso , tri-axial vibration sensor with temperature and acoustic sound , hipot tester , fundus camera //bid details2 / 73
Tender For tender for supply of procurement of scada pc accessories : : -27 inches full hd led monitors , internal solid-state drive sata 4tb , mini displayport thunderbolt to dp cable , dp to dp cable , hdmi cable , dp to hdmi cable , portable ips touch monitor 16 inch , mini dp to hdmi adopter , dp to hdmi adopter , alarm annunciation system , hand held high-speed air duster
Tender For supply of repairing strengthening of different types of housing of wt of chp , fabrication of nuts and bolts for slewing sector of old sr of size 24mm x 80mm , fabrication of nuts and bolts for wt side beam of wooden block of size 16mm x 165mm , fabrication of nuts and bolts for wt base housing of size 18mm x 130mm , fabrication of nuts and bolts for wt base grouting of pivot housing of size 33mm x 750mm , fabrication of rigid coupling nuts and bolts of 31. 7mm x 170mm size for wagon tippler of chp btps , fabrication of sector gear nuts and bolts of 30x130mm size for wagon tippler of chp btps , fabrication and machining of resilient plate fcu20 , fabrication and machining of resilient plate fcu16. 25 , repairing of damaged drive non drive end pinion of wt , repairing of damaged input pinion teeth of different type gear boxes of old and new sr , fabrication of suspension bar from old and used scrap material by complete machining and turning as required size 57x2680 63x2880mm of suspension bar for coal crusher , boring of required dia in runner half coupling of input pinion shaft motor shaft of conveyor system , repairing of brake drum coupling of wagon tippler gear box and motor , repairing of low speed coupling of conveyor system main route and sr , repairing of housing of bearing no 22244 kc3w33 , repairing of input pinion shaft and fluid coupling shaft of conveyor system , repairing of impeller and runner hub of fluid coupling , repairing of rigid coupling of wt , fabrication of shaft of tripper from old and used scrap material , repairing of input pinion shaft of transmission gear box of old sr hm121 and new sr hm135 , fabrication of pinion of slewing gear box of old sr hm121 and new sr hm135 by old and used scrap material , fabrication of hold back assembly for gear box of conv system , reclamation and repairing of fluid coupling ) /bid number: gem/2026/b/7272976 * /dated: 23-02-2026 & & / bid document1 / 18